3X:Chemistry Rust Converter instantly neutralizes rust and converts the rusted surface to a dark, protective polymeric coating. The inert coating provides an excellent primer base that seals out moisture to prevent future rust and corrosion. Protected surface can now be top coated with most paints.
Available in Aerosol, Quarts, Gallons, 5 Gallons & Drums.
PREPARATION. Remove all loose rust and dirt using a wire brush. Clean any residual grease and oils from the surface.
EQUIPMENT. Rust Converter can be applied with a brush, trigger bottle or a spray gun. Brush - A common household paint brush or foam applicator. Spray Gun - HVLP or conventional spray gun using a 1.0-1.4 nozzle at low pressure. Trigger Bottle - For best results, use in conjunction with brush. DO NOT use trigger bottle for any other products or disposed of after use.
APPLICATION. SHAKE WELL BEFORE USE. Rust Converter is ready-to-use right out of the bottle. No dilution or reducing is necessary. Liberally spray or brush the rust converter onto corroded surfaces. One quart will cover approximately 50-75 square feet on a smooth, non-porous surface. Irregular, porous or textured surfaces may require more product.
IMPORTANT. DO NOT return unused material to original container. DO NOT APPLY this product to painted surfaces. DO NOT APPLY this product to surfaces below 50°F. DO NOT allow this product to freeze.
DRYING TIME.The resulting coat will dry in about 20 minutes. Drying time may vary based on temperature. Apply a second coat to ensure complete transformation of rusted surfaces. Allow 48 hours of cure time before the application of the finished paint coat.
Rust Converter is effective on ferrous metals such as steel and iron.
Rust Converter contains tannic acid which chemically bonds then reacts with the rust to convert it to iron tannate. This results in a stable, black polymeric coating. Rust Converter reacts only areas where rust is present.
Yes. To prepare the surface, remove loose particles of rust and debris with a wire brush. Remove any grease, oil, or salt residue with a safety solvent or degreaser. Please note that any residue left on the surface may interfere with the adhesion of the product. It is important not to take it down to the bare metal. If so a metal primer is needed in place of the rust converter.
Aerosol covers 50-75 sq. ft.. Each quart will cover approximately 50-75 square feet. A gallon will cover about 200-300 sq. ft. Irregular, porous surfaces will require heavier application.
Yes, but only what was not poured from the bottle prior to application. Do not return unused product to the original container. Once the product comes in contact with metal the chemical reaction will contaminate any unused product.
Yes. Optimum results are obtained when the surface temperature and the product are between 50Â°F and 95Â°F. Do not apply if the surface temperature is below 50Â°F as this can cause the product to dry milky white or not fully adhere to the rust. If the temperature of the surface is significantly higher than 95Â°F, it can cause some of the components to evaporate too quickly and interfere with adhesion.
Simply clean application equipment with soap and water immediately after use.
Prime All is a high solids, advanced primer that seals surfaces for maximum coverage and hide.
Simply spray or brush 3X: Chemistry Paint Stripper on and scrub the paint off with ease.
3X:Chemistry Metal Prep combines a powerful flushing action with a high solvency formulation to remove brake fluid, grease, oil, wax and other contaminants on metal surfaces
3X:Chemistry Metal Etch inhibits rust and promotes paint adhesion for bare metal surfaces.
(Aerosol version) Chemically convert rust into a paintable polymeric coating.
Remove corrosion and rust without harming the metal.
A single component, high solids paint specially formulated to bond to blasted or rusted metal surfaces.
Multi-complex cleaner combined with genuine Carnauba Wax will give your car that "just waxed" shine after every wash.
This UV resistant cleaner shines 'n protects vinyl, rubber and plastic while restoring a natural, new look
This polymer based polish will renew your rides top coat with a deep mirror-like shine. Even works on oxidized paint.
This unique, one step aerosol polish features Carnauba Wax for shine, then seals the surface with Teflon® for a deep luster.
Nothing completes great wheels like sleek, shiny tires. This no wipe, long-lasting dressing will help you arrive in style.